Chemical Engineering · Subject 24

Chemical Engineering

McCabe–Thiele stages, sieve trays and the mole balance, on button-ups and ties, with socks to match.

Chemical Engineering

This week in Chemical Engineering,

A turnstile MOF sorts C6 rings, an organic sheet splits water unaided, crowded ruthenium cracks plastic toward methane, and a laser peels old panels for silver.

Get it by email

Download MP3

Behind the designs, a walk along one small chemical plant, drawn as a piping and instrumentation diagram in ISA-5.1 symbols, from the feed tank to the product tank. A fresh feed of A and its isomer P, half and half at 100 kmol/h, meets the reactor’s effluent and enters a 12-stage distillation column (11 sieve trays and a reboiler, feed on stage 6, reflux ratio 1.65, 1.5 times the minimum), which sends P at 95 percent to the product tank and A at 95 percent along the pipe rack to a 25.0 cubic meter stirred-tank reactor. There a first-order reaction turns 47.4 percent of the A into P in each pass, with a space time of 2.00 hours, and the loop carries the effluent back to the column, so that 90.0 percent of the A fed leaves as P. Each design card stands beside its unit: the column, the pipe rack (Reynolds number 134,734 in a 2-inch line, Colebrook friction factor 0.0211), the reactor and its Rushton turbine, the loop, the product control valve (flow coefficient 15.0, 71 percent open), the product tank and the stream table, whose balances close. Line width shows each stream’s molar flow and its color the mole fraction of P. After the walk the view pulls back to the whole plant. Computed; the plant is a model.

Welcome in

For anyone who has closed a mass balance

You know the hiss of a steam trap, the drone of a pump on its curve, and the moment a control loop stops hunting and settles. You have stepped off stages on graph paper, chased a mass balance that would not close until you found the purge, and read a friction factor off the Moody chart that you already half knew. You have argued whether a valve should fail open or fail closed. You remember the first time a column lined out: temperatures steady down the trays, product on spec, the plant doing what the flowsheet said.

Short-sleeve button-up · XS–4XL

TOTAL REFLUX

Separations: stage by stage, film by film, effect by effect.

Most of a chemical plant’s cost is separation. The McCabe–Thiele construction and the glass sieve-tray column it designs (12 theoretical stages, so the column has 11 trays plus the reboiler), the random packing of absorbers, Rillieux’s multiple-effect evaporator and the filter press. Total reflux is the column run with no product taken, the condition of minimum stages: here 6.4 by Fenske’s equation.

  • McCabe–ThieleMcCabe–Thiele as a brass instrument: a curved rod, a straightedge and a gold staircase of 12 steps.
  • The Distillation ColumnA glass sieve-tray column at work: 11 trays of froth above a boiling flask, the McCabe–Thiele staircase in glass.
  • Random PackingA loose heap of tower packing: white ceramic rings and saddles, and steel rings with their windows bent inward.
  • The Multiple-Effect EvaporatorThree copper effects in a row, the vapor of each boiling the next: Rillieux’s sugar evaporator.
  • The Filter PressA plate-and-frame filter press opened up, one thick cake of solids on its cloth: separation by squeezing.
Shop now · Regular price $65 Sale price $58.50

Leave your email and we’ll write the day it’s ready.

Medallion art in production.
In the incubator

FULLY DEVELOPED

Momentum, heat and mass: how things move through a plant.

Transport phenomena in five objects: Reynolds’s dye streaks, Nikuradse’s sand-lined pipes behind the Moody chart, the counterflow shell-and-tube exchanger, the static mixer that layers two fluids into 2ⁿ striations, and the sling psychrometer, where heat and mass transfer meet at the wet bulb. Fully developed is the insider’s word for flow that has stopped changing along the pipe.

  • Reynolds’s ExperimentThree glass tubes, three streaks of dye: a straight thread, a wavering one, and one torn apart into turbulence.
  • Nikuradse’s SandSix brass half-pipes lined with sand, the grains shrinking from coarse to almost smooth: the roughness behind Moody’s chart.
  • The Shell-and-Tube ExchangerA cutaway shell-and-tube exchanger, its tubes glowing red to amber, the shell side blue to teal: counterflow.
  • The Static MixerA glass pipe with six twisted blades and two resins inside: the layers double at every blade, 2, 4, 8 … 64.
  • The Sling PsychrometerA brass sling psychrometer: two thermometers side by side, the one with the wet wick reading lower.
Tell me when it’s ready

Leave your email and we’ll write the day it’s ready.

Medallion art in production.
In the incubator

SPACE TIME

Reactors: how long, how mixed, and how fast the molecules reach the catalyst.

Reaction engineering: the stirred tank against the plug-flow tube, the eggshell catalyst that the Thiele modulus explains, the fluidized bed, the Rushton turbine of every stirred reactor, and the honeycomb monolith. Space time, τ = V/v₀, is the reactor engineer’s clock, and a name a physicist will enjoy.

  • CSTR and PFRThe same pulse of dye in two reactors: spread evenly through a stirred tank, held as one sharp slug in a tube.
  • The Thiele ModulusWhite catalyst spheres, some halved to show a thin dark shell of metal: where the reaction actually happens.
  • The Fluidized BedA glass column of sand boiling like a liquid: bubbles of gas rising through it and bursting at its surface.
  • The Rushton TurbineA Rushton turbine in a baffled glass tank: a radial jet splitting at the wall into two loops, above and below.
  • The MonolithA cream ceramic honeycomb with a wedge cut away: thousands of square channels, their walls coated gray.
Tell me when it’s ready

Leave your email and we’ll write the day it’s ready.

Medallion art in production.
In the incubator

WORLD SCALE

The great processes, at the size that changed the world.

Five processes that define the industry: the Haber–Bosch loop and the Ostwald gauze, which together turned air into fertilizer; fluid catalytic cracking; the rotary kiln of cement and lime; and the hyperbolic cooling tower. A world-scale plant is the insider’s term for one built as large as the market allows.

  • The Haber–Bosch LoopThe ammonia synthesis loop as a steel-and-brass model: converter, cooler, separator full of liquid ammonia, circulator.
  • The Ostwald GauzeA stack of platinum–rhodium gauzes glowing orange: the catalyst that turns ammonia into nitric acid.
  • Fluid Catalytic CrackingA cutaway cat cracker: the riser, the reactor’s cyclones, the regenerator, and catalyst dark one way, light the other.
  • The Rotary KilnA cutaway rotary kiln model, tilted on its rollers, the firebrick glowing and the clinker tumbling toward the flame.
  • The Cooling TowerA hyperbolic cooling tower in pale concrete: a curved shell built of straight lines, standing on crossed columns.
Tell me when it’s ready

Leave your email and we’ll write the day it’s ready.

Medallion art in production.
In the incubator

P&ID

The plant as drawn: valves, meters, gauges, pumps and the last line of defense.

The piping and instrumentation diagram is the drawing a plant is built and run from. Its everyday objects: the air-to-open control valve, the float flowmeter, the rupture disk, the centrifugal pump on its curve, and the Bourdon gauge on every line.

  • The Control ValveA cutaway control valve: the plug in its seat, and above it the diaphragm and the spring that shuts it if air fails.
  • The Variable-Area MeterA tapered glass tube with a steel float hanging in it: the flow read straight off the glass.
  • The Rupture DiskTwo steel rupture disks: one domed and scored, one burst open into four petals.
  • The Centrifugal PumpA cutaway centrifugal pump: six backward-curved vanes inside a spiral volute that widens to the outlet.
  • The Bourdon GaugeA pressure gauge with its dial cut away: the C-shaped Bourdon tube, the toothed sector and the needle it drives.
Tell me when it’s ready

Leave your email and we’ll write the day it’s ready.

Short-sleeve button-up · XS–4XL

EQUATION STRIPE

From the general mole balance to NPSH, every line labeled.

Chemical engineering is balances and rates: what goes in, what comes out, how fast it reacts, and how hard it is to move, heat and separate. The Equation Stripe sets forty-five of the field’s equations in rows, each introduced by its name in capitals, so GENERAL MOLE BALANCE, FENSKE EQUATION and NPSH read at a glance. They follow a plant from its reactors through its columns and pipes to the valve that controls it: the ideal reactors and their residence times, catalysis from Langmuir and Hinshelwood to Thiele and Weisz–Prater, vapor–liquid equilibrium and the McCabe–Thiele lines, friction and heat transfer, humidity and the cooling tower, filtration, mixing and control.

Twenty-two rows carry the science of the page’s five picture designs. The other 23 are workhorses that need no introduction, from Raoult’s and Henry’s laws to the Ergun equation and the Chilton–Colburn analogy. Ammonia synthesis is written with its equilibrium arrow, ⇌, as chemists write it.

  • General Mole BalanceFA0 − FA + ∫rA dV = dNA/dt
  • Cstr DesignV = FA0X/(−rA)
  • Pfr DesignV = FA0∫0XdX/(−rA)
  • Space Timeτ = V/v0
  • First-Order CstrX = kτ/(1 + kτ)
  • First-Order PfrX = 1 − e−kτ
Shop now · Regular price $65 Sale price $58.50

Leave your email and we’ll write the day it’s ready.

Short-sleeve button-up · XS–4XL

CONCEPT STRIPE

The field’s ideas in its own words, with an equation every few units.

Some of chemical engineering is better said than written as an equation: a unit operation, a degree of freedom, a pinch, a fail-safe valve. The Concept Stripe sets forty-four of the field’s ideas in the same rows and type as the Equation Stripe, each after its heading: the foundations, separations, transport, reactions, the plant and its safety, and the history, from Course X at MIT in 1888 to fluid catalytic cracking in 1942. About one unit in four is an equation from the Equation Stripe, among them the Fenske equation, the Colebrook equation and valve sizing.

  • UNIT OPERATIONSArthur D. Little’s building blocks, 1915
  • REFLUXsend product back to buy purity
  • WET BULBthe coldest evaporation can reach
  • RESIDENCE TIMEhow long a molecule stays
  • FAIL-SAFEwhat the valve does when the air goes
  • BREAD FROM AIRHaber and Bosch fix nitrogen, 1913
Shop now · Regular price $65 Sale price $58.50

Leave your email and we’ll write the day it’s ready.

Socks mix and match across every field: three pairs for $69, and two ship free in the U.S.

Crew socks · One size

Crew socks

A field of your own, from cuff to toe.

  • The pattern
  • The previewA studio mockup; photos of the finished pair are on the way.
Shop now · Regular price $26 Sale price $23.40

Leave your email and we’ll write the day this pair is ready.

Necktie · 3.5 in wide

Subject ties

A formal introduction to your field.

  • The color
  • The previewStudio render of the tie. Zoom shows the print up close.
Shop now · Regular price $36 Sale price $32.40

Leave your email and we’ll write the day this tie is ready.

GENERAL MOLE BALANCEFA0 − FA + ∫rA dV = dNA/dt·CSTR DESIGNV = FA0X/(−rA)·PFR DESIGNV = FA0∫0XdX/(−rA)·SPACE TIMEτ = V/v0·FIRST-ORDER CSTRX = kτ/(1 + kτ)·FIRST-ORDER PFRX = 1 − e−kτ·CSTR RTDE(t) = e−t/τ/τ·TANKS IN SERIESE(θ) = n(nθ)n−1e−nθ/(n − 1)!·ARRHENIUSk = A exp(−Ea/(RT))·ADIABATIC RISEΔTad = (−ΔHrx)CA0/(ρcp)·THIELE MODULUSφ = L√(k/De)·EFFECTIVENESS FACTORη = (tanh φ)/φ (slab)·WEISZ–PRATER CRITERIONCWP = (−r′obs)ρcR2/(DeCs) ≪ 1·LANGMUIR–HINSHELWOOD−r = kKAKBpApB/(1 + KApA + KBpB)2·AMMONIA SYNTHESISN2 + 3H2 ⇌ 2NH3, ΔH° = −92 kJ (298 K)·AMMONIA OXIDATION4NH3 + 5O2 → 4NO + 6H2O·RAOULT’S LAWyiP = xiPisat·RELATIVE VOLATILITYy = αx/(1 + (α − 1)x)·RECTIFYING LINEy = Rx/(R + 1) + xD/(R + 1)·Q-LINEy = qx/(q − 1) − zF/(q − 1)·FENSKE EQUATIONNmin = ln[(xD/(1 − xD))((1 − xB)/xB)]/ln α·KREMSER EQUATION(yin − yout)/(yin − mxin) = (AN+1 − A)/(AN+1 − 1)·RACHFORD–RICE∑izi(Ki − 1)/(1 + ψ(Ki − 1)) = 0·ANTOINE EQUATIONlog10Psat = A − B/(C + T)·GENERAL MOLE BALANCEFA0 − FA + ∫rA dV = dNA/dt·CSTR DESIGNV = FA0X/(−rA)·PFR DESIGNV = FA0∫0XdX/(−rA)·SPACE TIMEτ = V/v0·FIRST-ORDER CSTRX = kτ/(1 + kτ)·FIRST-ORDER PFRX = 1 − e−kτ·CSTR RTDE(t) = e−t/τ/τ·TANKS IN SERIESE(θ) = n(nθ)n−1e−nθ/(n − 1)!·ARRHENIUSk = A exp(−Ea/(RT))·ADIABATIC RISEΔTad = (−ΔHrx)CA0/(ρcp)·THIELE MODULUSφ = L√(k/De)·EFFECTIVENESS FACTORη = (tanh φ)/φ (slab)·WEISZ–PRATER CRITERIONCWP = (−r′obs)ρcR2/(DeCs) ≪ 1·LANGMUIR–HINSHELWOOD−r = kKAKBpApB/(1 + KApA + KBpB)2·AMMONIA SYNTHESISN2 + 3H2 ⇌ 2NH3, ΔH° = −92 kJ (298 K)·AMMONIA OXIDATION4NH3 + 5O2 → 4NO + 6H2O·RAOULT’S LAWyiP = xiPisat·RELATIVE VOLATILITYy = αx/(1 + (α − 1)x)·RECTIFYING LINEy = Rx/(R + 1) + xD/(R + 1)·Q-LINEy = qx/(q − 1) − zF/(q − 1)·FENSKE EQUATIONNmin = ln[(xD/(1 − xD))((1 − xB)/xB)]/ln α·KREMSER EQUATION(yin − yout)/(yin − mxin) = (AN+1 − A)/(AN+1 − 1)·RACHFORD–RICE∑izi(Ki − 1)/(1 + ψ(Ki − 1)) = 0·ANTOINE EQUATIONlog10Psat = A − B/(C + T)·

The science on the shirt

What you’re wearing

Every object on the shirts, and the science behind it.

McCabe–Thiele

TOTAL REFLUX

McCabe–Thiele

12 stages at R = 1.65

McCabe and Thiele’s 1925 construction sizes a distillation column with a pencil: the equilibrium curve, two operating lines that meet on the feed line, and a staircase between them, one step per theoretical stage. For relative volatility 2.5, a 95 % top product and 5 % bottoms from a 50 % saturated-liquid feed at 1.5 times minimum reflux, it takes 12 steps, the feed entering on the 6th.

The Distillation Column

TOTAL REFLUX

The Distillation Column

Oldershaw, 1941

Vapor rises through the holes in each tray and bubbles through the liquid on it, while liquid flows across and down to the tray below: countercurrent contact, stage by stage. Oldershaw’s 1941 glass sieve-plate column lets the trays be watched, and its efficiency is close to a large column’s point efficiency, so it is still used to scale them up.

Random Packing

TOTAL REFLUX

Random Packing

Raschig, 1914

A packed column replaces trays with a bed of small hollow shapes that spread the liquid into thin films over a large surface while gas flows up through the gaps. Fritz Raschig’s plain ceramic rings, around 1914, came first; saddles, and metal rings with windows punched in their walls, followed, each giving more surface for less pressure drop.

The Multiple-Effect Evaporator

TOTAL REFLUX

The Multiple-Effect Evaporator

Rillieux, 1846

Boiling a solution in several vessels in series, each at a lower pressure, lets the vapor from one boil the next, so one kilogram of steam evaporates nearly as many kilograms of water as there are effects. Norbert Rillieux, born in New Orleans, patented it in 1846 for sugar; it still concentrates sugar, milk, pulp liquor and brine.

The Filter Press

TOTAL REFLUX

The Filter Press

cake on cloth, plate by plate

A filter press pumps a slurry into chambers between cloth-covered plates: the liquid passes through the cloth and the solids build up as cakes. As a cake thickens, the flow slows; at constant pressure Ruth’s 1935 equation makes the time grow with the square of the filtrate volume.

Reynolds’s Experiment

FULLY DEVELOPED

Reynolds’s Experiment

Re = ρvD/μ, 1883

In 1883 Osborne Reynolds sent a thin streak of dye down a glass tube of flowing water. Slow, it stayed a straight thread; faster, it wavered; faster still, it broke up and filled the tube. The change is governed by one number, ρvD/μ, now named for him: below about 2,000, flow in a pipe stays laminar.

FULLY DEVELOPED

Nikuradse’s Sand

r/kₛ = 15 to 507

To find how roughness drags on pipe flow, Nikuradse glued sorted sand grains inside smooth pipes at six relative roughnesses, pipe radius over grain size r/kₛ from 15 to 507, and measured friction over a wide range of Reynolds numbers. His 1933 curves are the measured backbone of the rough-pipe lines on Moody’s chart.

The Shell-and-Tube Exchanger

FULLY DEVELOPED

The Shell-and-Tube Exchanger

one shell pass, one tube pass

The most common heat exchanger in industry: one fluid flows through a bundle of tubes, the other around them in a shell, steered back and forth across the tubes by baffles. In counterflow the hot stream can leave colder than the cold stream leaves, and the heat duty is Q = UA ΔT_lm.

The Static Mixer

FULLY DEVELOPED

The Static Mixer

2ⁿ striations

A static mixer has no moving parts: helical elements in a pipe, each twisted through 180° and turned 90° to the one before, alternately left- and right-handed. Each element splits every stream in two and stacks the halves, so after n elements two fluids lie in about 2ⁿ layers, thin enough for diffusion to finish the job.

The Sling Psychrometer

FULLY DEVELOPED

The Sling Psychrometer

wet bulb below dry bulb

Two thermometers whirled through the air, one with its bulb in a wet wick: evaporation cools the wet bulb until heat flowing in from the air balances it, so the drier the air, the bigger the gap. With the dry-bulb reading it fixes the humidity on the psychrometric chart, and the wet bulb is the limit a cooling tower can approach.

CSTR and PFR

SPACE TIME

CSTR and PFR

E(t) = e^(−t/τ)/τ vs δ(t − τ)

Inject a pulse of dye. In a perfectly stirred tank it is everywhere at once and washes out exponentially, so some fluid leaves at once and some stays long; in a plug-flow tube it travels as a sharp slug and every element stays exactly τ = V/v₀. Danckwerts’ 1953 residence-time distributions are still how real reactors are diagnosed.

The Thiele Modulus

SPACE TIME

The Thiele Modulus

η = tanh φ / φ

In a porous catalyst pellet, reactant diffuses inward while it reacts. When reaction outruns diffusion (a large Thiele modulus, φ = L√(k/D_e)), only an outer shell does any work and the effectiveness factor falls toward 1/φ. So costly metal is often put only in that shell: an eggshell catalyst.

SPACE TIME

The Fluidized Bed

ΔP = weight of the bed

Blow gas up through a bed of fine particles fast enough and the pressure drop equals the bed’s weight per unit area: the particles float, and the bed bubbles, levels itself and flows like a boiling liquid, spreading heat almost perfectly. Winkler gasified coal in one in the 1920s; fluid catalytic cracking put it at the heart of refining in 1942.

SPACE TIME

The Rushton Turbine

six blades, four baffles

The standard stirred tank: a disc with six flat blades, a third of the tank’s diameter, set a third of the way up, in a tank with four wall baffles. It throws liquid outward in a radial jet that splits at the wall into two circulation loops, one above and one below. Rushton, Costich and Everett measured its power number in 1950: about 5 when turbulent.

The Monolith

SPACE TIME

The Monolith

square channels, coated walls

A monolith catalyst is a ceramic honeycomb of thousands of parallel square channels whose walls carry a thin porous coating loaded with precious metal. Gas flows straight through with little pressure drop while reactants diffuse to the walls. It is the reactor inside a car’s catalytic converter, and in many power-plant units that remove nitrogen oxides.

The Haber–Bosch Loop

WORLD SCALE

The Haber–Bosch Loop

N₂ + 3H₂ ⇌ 2NH₃

At about 450 °C and 200 bar over an iron catalyst only part of the gas reacts in one pass, so it runs in a loop: through the converter, chilled until the ammonia condenses out, topped up with fresh hydrogen and nitrogen, recompressed and sent around again, with a small purge for argon and methane. Haber showed it in 1909; Bosch’s BASF built the first plant in 1913.

WORLD SCALE

The Ostwald Gauze

4NH₃ + 5O₂ → 4NO + 6H₂O

Nitric acid starts with ammonia and air flashed across a fine woven gauze of platinum–rhodium at about 900 °C; in about a millisecond nearly all the ammonia becomes nitric oxide, and the gauze glows orange from the heat of its own reaction. Ostwald patented the process in 1902; with Haber–Bosch ammonia it turned air into fertilizer.

Fluid Catalytic Cracking

WORLD SCALE

Fluid Catalytic Cracking

first on stream, 1942

Hot catalyst powder meets oil vapor at the foot of a riser and cracks heavy molecules into gasoline-range ones within seconds as both rush upward. Cyclones separate the coked catalyst, which flows down to a regenerator where air burns the coke off and reheats it for the next pass. The first unit came on stream at Baton Rouge in 1942.

WORLD SCALE

The Rotary Kiln

clinker at 1,450 °C

A long steel cylinder lined with firebrick, tilted a few degrees and turning slowly, so solids tumble downhill toward a flame at the low end while hot gas flows the other way. In a cement kiln limestone and clay become clinker at about 1,450 °C. Rotary kilns, first used for cement in the 1880s, also make lime and alumina.

The Cooling Tower

WORLD SCALE

The Cooling Tower

a hyperboloid of lines

A natural-draft cooling tower is a hyperboloid of one sheet: a curved shell made of straight lines, strong and economical in thin concrete. Warm water falls through packing near its base while the warm, moist air inside rises by its own buoyancy, and evaporation cools the water toward the air’s wet-bulb temperature. Van Iterson and Kuypers built the first in 1918.

The Control Valve

P&ID

The Control Valve

air to open, fail closed

A globe control valve throttles flow by moving a plug toward its seat; a pneumatic diaphragm actuator on top moves the stem against a spring. In an air-to-open valve the spring closes it if the air supply fails, a choice made for safety on every valve in a plant. It is sized by Q = C_v √(ΔP/SG).

The Variable-Area Meter

P&ID

The Variable-Area Meter

the float finds its level

A float in a tapered glass tube rises until the gap around it lets the flow past with just enough drag to hold up its weight: more flow, a wider gap, a higher float. The etched scale on the glass reads the flow directly, with no power. It has sat on laboratory gas lines and pilot plants since the early twentieth century.

The Rupture Disk

P&ID

The Rupture Disk

burst at set pressure

A rupture disk is a thin domed metal membrane made to burst at a set pressure, opening an instant, full-bore vent: the last line of defense when a vessel overpressures. Scored disks open along their score lines into petals and do not fragment. One is often fitted under a relief valve to protect it from a corrosive process.

The Centrifugal Pump

P&ID

The Centrifugal Pump

pump curve meets system curve

A spinning impeller flings liquid outward into a spiral volute that turns its speed into pressure. The pump runs where its falling head–flow curve meets the rising curve of the piping system. If the pressure at the impeller’s eye falls below the liquid’s vapor pressure it boils there, and the collapsing bubbles cavitate the vanes.

P&ID

The Bourdon Gauge

Bourdon, 1849

Pressure inside a curved, flattened tube tries to straighten it; the tip’s small movement, magnified by a geared sector and pinion, swings the needle around the dial. Eugène Bourdon patented it in 1849, and it is still the gauge on nearly every vessel and line in a plant.